Natural Stone Sealer - WET LOOK
Protective 'wet look' Natural Stone Sealer. Not Suitable for Polished or Kandla Grey Sandstone (Sample + 3 sizes)
Smartseal Natural Stone Sealer WET LOOK is a water-based protective sealer that creates a durable, clear silk/satin finish. It can be used on internal and external surfaces made from sandstone**(see exceptions below), limestone, slate, terracotta, quarry and Victorian tiles, brick pavers and any textured stone or masonry surfaces.
Smartseal Natural Stone Sealer WET LOOK is rapid drying and very easy to apply. It will provide protection to the applied surface against oil and water-based stains.
- Ideal for Natural Stone**(see exceptions below) & Slate
- Provides a Silk/Satin or "Wet-look" finish
- Ok for rough & absorbent surfaces
- Suitable for outdoor or indoor use
Please take a look at the other sealers for natural stone such as the DRY finish Natural Stone Sealer. For a colour enhancing sealer for natural stone that is not a gloss finish, you might want to consider the Natural Stone COLOUR ENHANCER.
*WE DO NOT RECOMMEND USING ON POLISHED STONE & CERAMIC GLAZED SURFACES, AS IT WON'T SOAK INTO THE SURFACE*
**Exceptions to Sandstone suitability:
Please note this product is not suitable for Kandla Grey (mid and light grey) sandstone
COVERAGE RATIOS:
Average 5-12 m² per litre depending on the texture and porosity of the surface being sealed.
APPLICATION INSTRUCTIONS:
Due to the effects of Efflorescence and Natural Salts and Minerals, that can permeate through Natural Stone, it is recommended not to seal for a minimum 4 months after installation.
1. Apply in temperatures above 15°C, but below 23 degrees ensuring the surface is completely dry, clean and free from debris. Apply only if no rain is forecast for at least 8 hours. For best cleaning results use Patio Clean Xtreme.
**If applied to a surface where a "sweep-in" pointing compound has been used with the last 6 months, the natural stone must be fully cleaned with Smartseal Residue Remover prior to sealant application.**
2. Apply the sealer thinly and evenly with a low pressure sprayer, roller, microfibre mop, paint brush or soft cloth. Try not to leave application marks or allow the product to 'pool' or 'puddle' on the surface immediately after application. In the event of over application please ensure all excess is removed within 45 minutes of applying.
3. Once applied, allow minimum 60 minutes drying time before applying the second coat. If possible, apply the product in the opposite direction to try to achieve an even finish. Multiple coats can be applied to achieve the desired finish.
Important Note: Any areas nearby that are not being sealed should be protected with masking materials. If you are sealing over coloured grouts, carry out that a stain test before proceeding.
Q: Is ot possible to remove this? I put it on concrete tiles and looks awful
A: The wet look sealer should onky be used on natural stone. If you want to remove it you would need to use the residue remover and apply it neat so it acts as a sealer stripper
Q: Can the wet look sealer be power washed or cleaned of green leaf plant stains months later? My patio suffers from surrounding plant leaf drips over winter damp months
A: The wet look sealer can be cleaned afterwards. But pressure washing would to some degree reduce the lifespan of the sealer. We would recommend when 'green algae' starts to form, applying diluted 'Green Clear' Biocide. This will resolve the issue, without pressure washing and act as a preventative. Hope that helps.
Q: I have just used the wet look natural stone sealer, the instructions say about 8 hours of dry weather, what happens to the stones if it rains after 2/3 hours of application. Thanks
A: If the product has not cured before it gets wet, it is likely to go white on the surface as the sealer becomes diluted and unable to dry correctly. Hope that helps
We provide a national delivery service for our block paving sealer, pattern imprinted concrete sealer, roof coatings and tarmac restorer on a standard 2 - 4 working day basis. Dependent on weight, this is normally done by pallet or parcel carrier.
If you need products delivered quicker, for a small additional charge, orders placed before 1.30pm can be delivered within 1 - 2 working days to most parts of the UK, although this is dependent on the courier service in your area and the product/s ordered. If you require this service, please check on area availability by calling 01268 722500.
Our commitment is to supply all orders as placed and we offer a comprehensive guarantee of quality. Providing a reliable delivery service to all our customers is most important to us and this is backed up by the many satisfied customer testimonials we have received over the years.
If you need an order delivered to a different address, left somewhere at your property without a signature or left with a neighbour, just let us know.
We also try to maintain 100% stocking levels of our products at all times, so an immediate despatch is virtually guaranteed.
Our product returns policy can be viewed by visiting our Terms and Conditions section.
*Free delivery on orders over £75 are subject to the delivery address location.
Very satisfied so far with the wet look sealer. Time will tell if it is easier to keep the patio clean.
An Indian sandstone area that has been laid for several years and become drab and more like cement slabs. After jet washing, the colours returned, most attractive as it was when new, but when dry, it was not as effective. I used Ultimate Enhancer sandstone sealer and the results are truly amazing. It now has the colours that showed when wet. Very pleased. I found the technical team extremely quick in response to my questions.
Was sceptical to whether this sealer would actually provide the finish desired; however 3 coats on prepared sandstone give a lovely wet sheen which is easily cleaned. Longevity, time will tell. The result is however a little slippery when wet which can be an issue subject to type of footwear.